Bộ Phát Xung DKC-1A

350,000₫

Product Details

Share:
Q.ty:
Compare

http://bamien247.com/

Bộ Phát Xung DKC-1A

Điện áp: 6-32 VDC

Dòng:0.1A

Dải tần số:1-20KHz

SƠ ĐỒ  CHÂN

Bổ-sung-ĐKC-1A-Bước-điều-khiển-động-cơ-xung-máy-phát-điện-Servo-tốc-độ2

 

1 positive transfer limit
2 inversion limit
3 stop
4 start
5 common end(general pin)
6 potentiometer

so do dau noi DKC-1A

Description:

  • Wide voltage input,6-32DC;
  • With a power anti-reverse polarity protection, overvoltage protection, overcurrent protection, complete protection of the safety controller
  • Input signal is a bottom-level input;
  • OptimizedS -type acceleration curve
  • Maximum output frequency can be achieved20K
  • All input and output optocoupler isolation
  • Board plant potentiometer speed control, external potentiometer speed automatic switching
  • A variety of functions, set up a simple, functional and practical
  • Function modes are:
  • 1: Automatic mode and from the
  • 2: Single Entry Mode
  • 3: One-Shot mode
  • 4: Jog mode:( Automatic control applications a roundtrip mode)

1EquipmentAPointBRunning back and forth between points.

After the device is powered, external trigger startRun, run to the equipmentAForward-point limitAfter running to automatically reverseBpointAfter reversing limit,And running forward toAPoint, so run back and forth. Until the trigger to stop the motor stops running.

parameter settings:

1.Set upSW1 = OFF , SW2 = OFF(Roundtrip automatic mode)

2. Onboard SpeedOr external potentiometer,Adjust the appropriate speed.

 Control application two single-shot mode:

1 Equipment fromAPoint to B After stopping point. Start again the device stops from point A to point B.

After the device is powered, external trigger startRunning from the device toApointStarting to run when the deviceBForward-point limitAfter the machine stops running, if you start again from point B to reach the trigger deviceAPoint, the device stops. start upA-> B stop, start, B-> A stop motion. If the trigger to stop the motor running in the device stopped immediately.

parameter settings:

1. Set upSW1 = OFF , SW2 = ON(One-Shot mode)

2. Onboard SpeedOr external potentiometer,Adjust the appropriate speed.

Control using three single round-trip mode:

1 Equipment from a Point to a B point after returning to the stop.

After the device is powered, external trigger start Running from the device to A point Starting to run when the device B Forward-point limit, The device runs reversely, when the arrival A Point, the motor stops. Complete a

A-> B-> A movement. If the trigger to stop the motor running in the device stopped immediately.

parameter settings:

1. Set upSW1 = ON , SW2 = OFF(Single round-trip mode)

2. Onboard SpeedOr external potentiometer,Adjust the appropriate speed.

Application of the Four 🙁 control jog mode)

1Full stop and external switch controller starts, reversing.

After the device is powered to start the bottom level of the input motor running forward,

                The bottom level of the withdrawal, the motor stops.

                To stop the input of the bottom level of the reverse motor running,

                The bottom level of the withdrawal, the motor stops.

parameter settings:

    1.Setting SW1 = the ON  , the ON SW2 =(Jog mode)

2. Speed ​​board or external potentiometer,Adjust the appropriate speed.

 

Đánh giá

Chưa có đánh giá nào.

Be the first to review “Bộ Phát Xung DKC-1A”